250kva power kavach offered for factory in banglore
Power Kavach is protection device meant for 440V protection in any individual phase and spike protection
This is a case which is handled by our Dealer in Bangalore – : Power engineers- 9845003327. You can connect with them in case you need a similar solution for your requirement
They are offering a solution where Power Kavach is going to be used along with Servo stabilizer to give a comprehensive solution.
Servo stabilizer is installed for voltage regulation and stable voltage where as Power Kavach gives 440V protection in each phase and spike protection.
Get in touch with us on 9769996205 or email to us on asm@microsystemservices if you would like to know more.
We are looking for dealers all across India who would like associate with us in the quest for Safe electricity for all.
To find out MSS dealer in your area click on this link
New model of power kavach : 3kva with 3 pin socket output
We are looking for dealers all across India to reach out to customers who have faced neutral open and spikes related problems.
Click here To know more about power kavach
Please reach out to us on 9769996205 or email us on Asm@microsystemservices.com
Equipower plus installed in Bangalore for lift protection by our dealer
This is a mainline voltage protector installed in mumbai for Lift protection. The installation is done by our dealer in Bangalore. They were also concerned about problems like neutral open which can cause 440V in any particular phase.
Installation done by Urja solutions, Bangalore. Contact :9844933433.
Equipower will protect against neutral open, double phasing, double voltage , 440V in any individual phase for more than 24 hours. It is designed for this purpose specifically.
#Equipower™ is a voltage protector which is connect in your main line and it protects all equipments connected through it. It can easily protect your equipment from voltage as high as 440V in single phase and that is what makes it special
It also acts as an insurance against power fluctuation that could damage your electrical appliances and electronic devices used in your homes and offices .
#Equipower™ protects your electrical appliances and electronic devices against high voltage, low voltage, surges, spikes. However what sets it apart from other protection devices is the ability to protect your equipment in case of #neutralopen and #doublephasing problems.
Most of Equipments deteriorate very quickly after the warranty period. #Equipower™ increases life of equipments and minimizes the risk of damage.
For queries, you contact us on 9769996205 or fill the form below
VMC machine PCB damaged inspite of having a stabilizer
We had a case where a VMC machine already having a stabilizer installed for it. However one of PCB was damaged in spite of having stabilizer. This is situation that happened after 4 years of installations. The stabilizer was from reputed make and was in good working condition. The VMC machine is from reputed international make.
Why did the VMC machine get damaged inspite of having stabilizer installed?
A servo stabilizer is voltage conditioner which stabilizes or brings the voltage to set point even if there any variations in voltage in the input. So if you want a stable supply then you will need a Stabilizer
However Stabilizer has 2 major limitations.
1. Response time: If the voltage shoots up to above 300V in any phase, the stabilizer will take atelast 6-7 seconds to cut off the supply to the equipment. In one second 50 cycles of high voltage supply pass in to the equipment and this can damage the equipment. So you need something that can cut off immediately when this happens.
2. Spikes: In a normal day , your equipment faces atleast 100-200 spikes , all of which pass through the stabilizer with out any resistance in to the equipment damaging it little by little. Equipment gets damaged over a period of 4-5 years. Spikes have duration in microseconds and stabilizer cannot react in such a short interval.
Our solution:
The solution we offered was in 2 steps.
1. Equipower- Main line Voltage protector with 20kA spike protection
We offered a 100A Equipower with single phasing preventor for complete premises so that it can handle problem of neutral opn or double phasing. In case of extreme over voltage it will cut off in fraction of seconds thereby saving the equipment from over voltage situation caused by external situations. It also has in built spike protection which prevents external spike from coming into the factory premises. Since there are other factory galas in the industrial estate, there is possiblity of spikes from other premises coming into the factory. So an Equipower at the main incomer helps in solving both of these issues.
2. Spike protection for individual machines
Each individual machine itself generates a spikes of its own and that is experience by other machines. There were several lathe machines and some CNC machines in the factory. Since the CNC machines were critical in nature we placed spike protection units at the individual CNC machines so that spikes from other machine do not enter in the CNC machine and damage the electronic PCBs over time.
MSS 